can220 ip installation
can you tell me what if a standard cat6 network cable wired to T568A will work between the POE and the CAM220 ip the run to the camera is 80ft. thanks Dennis
View ArticleSeatalk Fail / SmartPilot
Seatalk Fail Error Equipment: Smart Pilot ST7001 & ST-50 Tri-Data Blindly running new rubber fuel line under the floor I would have crossed over two cables. I suspect the Fluxgate cabling would be...
View ArticleTroubleshooting a SeaTalk communications failure
SeaTalk communications failures (STLK FAIL) as reported on an autopilot's control head, ST60 Wind Instrument's LCD flashing two square boxes, or cessation of SeaTalk communications between all...
View ArticleWI FI chirp Sonar
Hello, just got my Wi Fi chirp down vision sonar setup and just installed it, my question is where is the noise suppressor that came with it suppose to be installed at? I don't even see it list on the...
View ArticleProduct Selection Advice needed...
From Ray marines list... - a list of the marine electronics products which are presently installed onboard the boat: E120 (older generation) Furuno Radar 1835 SIMRAD AP 28 Autopilot I also have a RM...
View Articlee95 reboots when starting engine
I recently upgraded the E80 Classic MFD on my Beneteau 393 to an e95. I am now experiencing spontaneous reboots of the MFD whenever I start the diesel engine. This had never occurred with the E80...
View ArticleVoyage Planner Scanning for my E127
My Voyage Planner is opened, my E127 is turned on. WiFi on both PC and E127 are turned on. yet my Voyage Planner scans, but can not find the E127, yet the E127 shows it is connected to my home Network....
View ArticleST4000 plus w/ E80 as navigator over SeaTalk 1 bus
Hello all, Has anybody used the E80 as the source of ST4000+ track information over the SeaTalk 1 bus. I want to allow the ST4000+ to continue to use the analog compass (which is directly connected to...
View ArticleSeatalk converter ST60+not on ng backbone
Installed Seatalk to Seatalk ng Converter. LED lights indicates "healthy" connection status. Depth does not repeat to a78 or P70 via ng backbone. Request MFD to find depth device and not found. Advise,...
View ArticleNavionics charts to E-120
I have a classic E-120 which has an older Navionics+ CF card installed. I'm going to be updating my system soon, but currently would feel more comfortable with a new Navionics card. I know there are...
View ArticleECI-100 Question
Hello, I was wondering is it true if I have an ECI-100 used for a motor from one boat and I buy a different boat and move the ECI-100 to the new boat that it has to be factory reset? So, the ECI-100 is...
View ArticleVessel icon appears to be incorrectly oriented
Two of the most commonly confused navigational terms are heading and course over ground (COG). Heading is the angular designation of the orientation of the vessel with respect to true or magnetic north...
View Articlec127 "Follow From Here" Waypoint Issue
I am running a two station setup with a new c127 and a legacy C120 connected through a Seatalk to SeatalkNG converter. I use the c127 as the primary route navigation source and am running software...
View ArticleS100 Did I buy the wrong model?
Just bought an S100. It has the Sea Talk 3 pin plug on the base station. My current instruments are all Sea Talk ng products. Connectors are not compatable. A literature search shows a converter kit...
View ArticleUpgrading MFD
I'm considering upgrading from a Classic E-120 to either an eS97 or eS127. Rather than completely rewiring the helm, I'd like to have the option of doing the wotk in phases. Currently my RS130 is...
View ArticleSuncover slipping down the display
Does anyone have any hints as to how to prevent this? After about four to six hours, in a variety of temperatures, the cover slips down the display so that the display is no longer protected from the sun.
View Articleconnect external gps source to SeatalkNG
I have the bare wire ends sea talk cable plugged into my SeatalkNG system. Can I hook the GPS NMEA outputs from my vhf into this system so the autopilot can steer to a waypoint? which of the bare wires...
View ArticleHardover time
I have installed an ST4000 wheel pilot w ACU100 and sea talk NG Backbone. How do I determine the hardover time setting? The manual suggests setting this, but gives no instruction for how to do it.
View ArticleHow do I determine hard over to hard over time?
Hard over to hard over time may be determined by the following procedure: 1) disconnect the motor leads from the autopilot course computer 2) momentarily connect the motors leads to +12 VDC and ground...
View ArticleST60+ Tridata VMG
I have a Raymarine ST60+ Tridata instrument which will display VMG information for a few seconds and then it reverts back to the current speed display function. Is there a way to have the VMG display...
View Article