My ES127 screen will flicker and go dark with either a voltage rise (approx. 13.6) or drop (approx. 11.6).
Specs say 10.8 to 31.2
Greg
Specs say 10.8 to 31.2
Greg
↧
Input voltage
↧
ST60 Wind Transducer
My St60 Wind Transducer (Wind direction) has stopped moving. After removing it from the masthead, it was discovered that it is rusty/corroded and is likely in need of replacement. My question is: Can I use the same cable and purchase a R28170 or would I need to purchase the E22078 with the cable?
Thanks,
Steve
Thanks,
Steve
↧
↧
Power Cable for eS128
I have an eS128 mfd that I would like to bench test at my home. I need an appropriate Raymarine power cable to connect the eS128 to a 12v power supply at my home. I have been unable to find out if Raymarine sells such a cable and, if so, what the part number would be for ordering purposes.
I would much appreciate it if you could let me know if Raymarine does sell such a power cable.
Many Thanks
Mikeyor
I would much appreciate it if you could let me know if Raymarine does sell such a power cable.
Many Thanks
Mikeyor
↧
Unable to Connect IP Camera to a Seatalkhs Switch
This thread is being posted to obtain input for a solution to connectivity issues with an IP camera, model number IRIS 710.
The camera is connected to a Seatalkhs switch which in turn connects to two e125 MFD’s, neither of which are able to detect the camera. In addition, the green light where the CAT5 Ethernet cable connects does not illuminate green indicating no communication.
One complication is that the disc containing the manufacturer’s IRIS Centre Software intended to communicate to the IRIS 710 camera was damaged precluding the ability to run the software.
The IRIS 710’s Installation and Operation guide states the camera will adopt an IP address provided by the Router / DHCP server.
Question: is the Seatalkhs switch the same thing as a Router / DHCP server and are there any other suggestions to resolve this issue?
The camera is connected to a Seatalkhs switch which in turn connects to two e125 MFD’s, neither of which are able to detect the camera. In addition, the green light where the CAT5 Ethernet cable connects does not illuminate green indicating no communication.
One complication is that the disc containing the manufacturer’s IRIS Centre Software intended to communicate to the IRIS 710 camera was damaged precluding the ability to run the software.
The IRIS 710’s Installation and Operation guide states the camera will adopt an IP address provided by the Router / DHCP server.
Question: is the Seatalkhs switch the same thing as a Router / DHCP server and are there any other suggestions to resolve this issue?
↧
RayData to Raymarine ST60+ Tridata
A Raytheon RayData instrument is installed on a small sailboat I purchased a few years ago. Though the information arriving at the display seems to be accurate, the display itself is failing. Considering the instrument may be around 20 years old, I’d say it has performed pretty well. But now it needs replacing.
Assuming that the transducers and their cables are compatible, it appears that the instrument to be the replacement is a Raymarine ST60+ Tridata. If that is the case, it looks like I may have to make two modifications:
1. Perhaps modify the bulkhead mounting [censored](s)
2. Modify the pigtail connector coming from the depth transducer
I feel confident I can perform both of these modifications, so now I have two questions:
1. Can indeed the Raymarine ST60+ Tridata can be used as a replacement, and
2. Is there a depth transducer, pigtail adaptor available that can save me some time in sorting that cable to make the correct correction?
Thank you for your help.
Assuming that the transducers and their cables are compatible, it appears that the instrument to be the replacement is a Raymarine ST60+ Tridata. If that is the case, it looks like I may have to make two modifications:
1. Perhaps modify the bulkhead mounting [censored](s)
2. Modify the pigtail connector coming from the depth transducer
I feel confident I can perform both of these modifications, so now I have two questions:
1. Can indeed the Raymarine ST60+ Tridata can be used as a replacement, and
2. Is there a depth transducer, pigtail adaptor available that can save me some time in sorting that cable to make the correct correction?
Thank you for your help.
↧
↧
Axiom crashes
I've had an Axiom 9 NAG for a week and have been playing with it both on the bench and in a prototype-installation on the boat. During that time I've had about 10 crashes, mostly (I think) while interacting with the display.
I'm not concerned about this. I don't have things installed in their final configuration yet and I realize LH3 is an evolving product.
Fortunately LH3 generates crash logs. My question is: When does RM want to receive crash reports and should the logs be included?
Some shops I've worked with only want to hear about errors that are readily reproducible. Other places want to see every crash log (which they aggregate to spot trends).
What does RM prefer at this point?
I'm not concerned about this. I don't have things installed in their final configuration yet and I realize LH3 is an evolving product.
Fortunately LH3 generates crash logs. My question is: When does RM want to receive crash reports and should the logs be included?
Some shops I've worked with only want to hear about errors that are readily reproducible. Other places want to see every crash log (which they aggregate to spot trends).
What does RM prefer at this point?
↧
Heading Alignment SPX-30
I have problems with the heading alignment changing and varying up to 30 degrees port and starboard with my SPX-30 pilot. The unit will track properly to a way point and follow a course with no issues. However, when in heading mode the vessel will change course as the heading moves. I can watch this happen on the chart plotter. The vessel indication will stay constant and the chart rotates as the vessel changes heading (verified by oil filled compass). When tracking a course or going to a point the orientation of the vessel on the chart plotter screen rotates. All equipment is Raymarine less than 4 years old all communicating via Seatalk-NG. Installed on a sailboat. No messages or errors. Replaced fluxgate compass with no results. I have had the core pack repaired by Raymarine and it worked properly for a few weeks then started doing it again. I replaced the core pack with a new unit and it worked well for about 6 weeks and it has started doing the same thing. Question: Is this a known issue with the SPX-30? What could be causing the same repeated failure?
↧
A65 & EV100 Power Installation ???
Have an older A65 (gps and ff combo) and love it! Finally after 8 years of wanting and needing, I got an EV100 power autopilot. Going on 23' Seaswirl w I/O V8, ocean only.
1. Do I/should I/Can I connect the ev100 to the gps ?? the only open port on the back of the gps is the "Aux" port. the other 4 are taken (gps, sonar, power and nmea0183 connected to my vhf).
2. Is my A65 the old Seatalk? I see the converter kit E22158
3. Whats the difference of hooking it up to my gps or not hooking it up ?
thx for your help and insight
![.jpg]()
20160606_164213.jpg (Size: 115.9 KB / Downloads: 2)
1. Do I/should I/Can I connect the ev100 to the gps ?? the only open port on the back of the gps is the "Aux" port. the other 4 are taken (gps, sonar, power and nmea0183 connected to my vhf).
2. Is my A65 the old Seatalk? I see the converter kit E22158
3. Whats the difference of hooking it up to my gps or not hooking it up ?
thx for your help and insight
20160606_164213.jpg (Size: 115.9 KB / Downloads: 2)
↧
eSeries (e125) and today's waypoints bug
I have an e125 with software v19.03, and noticed this summer a bug when displaying waypoints by groups. On Saturday, September 2nd I was heading south on the Potomac River towards Chesapeake bay, and saved several new waypoints. At one point I was checking the waypoints, and filtered them to display only "today's" waypoints. I saw a few waypoints from near Beaufort, NC - and hadn't had the boat in NC since 2014!
On closer inspection, I noticed the NC waypoints just happened to be created on the same month and day - September 2nd - but the year was 2014. So it looks like the display filter mask only compares month and date, but not year. Has anyone else seen this?
On closer inspection, I noticed the NC waypoints just happened to be created on the same month and day - September 2nd - but the year was 2014. So it looks like the display filter mask only compares month and date, but not year. Has anyone else seen this?
↧
↧
Connecting a Axiom Pro 12 S in place of a RC530
I recently purchased an Axiom Pro 12 S to replace my sailboat's RC530 chart plotter as well as a Quantum Radar to replace a 15 year old analog Raymarine Radome.
I need help to make a connection between the in place the older cable that carries power and the NMEA 0183 wires to the Navpod at the binnacle.
The new cable for NMEA 0183, Video, Power has: Red, Black, and female BNC connectors that I know what to do with. It also has White, Yellow, Brown, Green, Orange with gray stripe, and Orange with white stripe. I understand that those are for the NMEA 0183.
The older cable has Red and black that I know go to + and - battery and also Yellow, Green, Blue, Orange, and a bare (uncoated) wire.
Please tell me what connections should I make between the wires in the old cable and the new cable in order to have the NMEA 0183 functional.
The other equipment that the system has is a ST6001+ autopilot, ST60 tridata, ST60 speed, and a remote for the autopilot. I plan to soon add a Raymarine AIS transponder.
Thanks!
Jeff
I need help to make a connection between the in place the older cable that carries power and the NMEA 0183 wires to the Navpod at the binnacle.
The new cable for NMEA 0183, Video, Power has: Red, Black, and female BNC connectors that I know what to do with. It also has White, Yellow, Brown, Green, Orange with gray stripe, and Orange with white stripe. I understand that those are for the NMEA 0183.
The older cable has Red and black that I know go to + and - battery and also Yellow, Green, Blue, Orange, and a bare (uncoated) wire.
Please tell me what connections should I make between the wires in the old cable and the new cable in order to have the NMEA 0183 functional.
The other equipment that the system has is a ST6001+ autopilot, ST60 tridata, ST60 speed, and a remote for the autopilot. I plan to soon add a Raymarine AIS transponder.
Thanks!
Jeff
↧
Wireless display / Miracast setup tips?
Has anyone gotten the new Wireless Display / Miracast stuff working in v3.2 from an Axiom MFD? I have tried a number of devices which are Miracast capable, but I never see them on the MFD as being an available device to cast to.
Devices I have tried:
Samsung TV with miracast
Vizio TV with Roku connected and miracast enabled
Samsung TV with Roku connected and miracast enabled
Is there a specific version of Miracast that is supported, or a particular limit or list of devices supported? I can confirm that I can cast to these devices from other devices (like an Android phone, which I know LH 3.x is built off of) without any issues.
The Axiom is on the same WiFi network as everything else, I can see it there via other means, and it gets software updates that way as well, so I know connectivity is good. I've restarted all of the devices in question in various orders but have not seen any difference - the MFD never shows any available wireless displays.
Devices I have tried:
Samsung TV with miracast
Vizio TV with Roku connected and miracast enabled
Samsung TV with Roku connected and miracast enabled
Is there a specific version of Miracast that is supported, or a particular limit or list of devices supported? I can confirm that I can cast to these devices from other devices (like an Android phone, which I know LH 3.x is built off of) without any issues.
The Axiom is on the same WiFi network as everything else, I can see it there via other means, and it gets software updates that way as well, so I know connectivity is good. I've restarted all of the devices in question in various orders but have not seen any difference - the MFD never shows any available wireless displays.
↧
EV-150 - Hydraulic line connections
Is there a specific hydraulic lines need to be connected to the type 1 pump.
The ports are labeled A - B - R
R = Reservoir
A = Port?
B = Starboard?
I haven't installed the pump yet and want to make sure it's connected properly.
The ports are labeled A - B - R
R = Reservoir
A = Port?
B = Starboard?
I haven't installed the pump yet and want to make sure it's connected properly.
↧
3D Real Vision Transducer placement (Yacht)
Hello,
I am looking for some input about putting 3D Real Vision Transducer on a Hood 38 yacht and whether I can get away with 1 transducer instead of 2.
I am currently thinking forward of the keel on the center line on a fairing block would be best:
https://imgur.com/a/gq0TM
Q: Does the fore/aft line of the transducer need to be parallel to the waterline/oceanfloor?
https://imgur.com/a/KPt8g
https://imgur.com/a/l8HBv
I am also concerned that the threaded part of the transducer wont be long enough to go through the wedged fairing block and the hull.
Has anyone else done this on a yacht?
I was going to use the bronze transducers as I hear the plastic ones still have a few teething problems?
Cheers
W
![.jpg]()
20171117_154652_resized.jpg (Size: 474.97 KB / Downloads: 2)
I am looking for some input about putting 3D Real Vision Transducer on a Hood 38 yacht and whether I can get away with 1 transducer instead of 2.
I am currently thinking forward of the keel on the center line on a fairing block would be best:
https://imgur.com/a/gq0TM
Q: Does the fore/aft line of the transducer need to be parallel to the waterline/oceanfloor?
https://imgur.com/a/KPt8g
https://imgur.com/a/l8HBv
I am also concerned that the threaded part of the transducer wont be long enough to go through the wedged fairing block and the hull.
Has anyone else done this on a yacht?
I was going to use the bronze transducers as I hear the plastic ones still have a few teething problems?
Cheers
W
20171117_154652_resized.jpg (Size: 474.97 KB / Downloads: 2)
↧
↧
Retired FAQ database for legacy / retired Raymarine products
Retired FAQ database for legacy / retired Raymarine products
Please note that the latest FAQs for Raymarine products may be found within this Forum. Please click here to view the FAQ addressing how one may search this Forum for FAQs. Should you have a legacy / retired product for which you were unable to locate and FAQ addressing the the subject which you are seeking assistance with, then it is recommended that the Retired FAQ database for legacy / retired Raymarine products be searched.
![[Image: attachment.php?aid=1400]]()
RAYFAQ#
![.jpg]()
Clipboard03.jpg (Size: 13.69 KB / Downloads: 8)
Please note that the latest FAQs for Raymarine products may be found within this Forum. Please click here to view the FAQ addressing how one may search this Forum for FAQs. Should you have a legacy / retired product for which you were unable to locate and FAQ addressing the the subject which you are seeking assistance with, then it is recommended that the Retired FAQ database for legacy / retired Raymarine products be searched.
RAYFAQ#
Clipboard03.jpg (Size: 13.69 KB / Downloads: 8)
↧
Axiom Waypoint Unable To Download
I am trying to import waypoints from an SD card my Axiom 7 won't accept the import. I tried a GPX file and a FSH file but neither works. Does anyone have a suggestion?
↧
Transducer adapter for a Raymarine E7
I have a "Airmar" Ray marine A80150 transducer. It will not plug directly into my Raymarine hybrid touch E7. is there adapter for this or do I need a different transducer? The manual said this one would work.
Thanks
Tom
Thanks
Tom
↧
Ray70 software update
Cannot find the link to download Ray70 software on the download page. Can you provide the download link.
Thank You
Thank You
↧
↧
DSM 300 issues
Good Morning,
I recently purchased a boat equipped with The following Raymarine electronics:
E140W Hybrid display
RS125 GPS antenna
E92143 4KW Radome
DSM300
Ray240 VHF
And I just installed a TM258 transducer to replace a P66 that the previous owner had knocked off.
On my short test rides after installing the TM258 everything ran fine. However on Sat I ran out 30 miles into Gulf of Mexico. Max depth 100'. Everything ran good until about 20 miles out, 70' of water. Then I first lost scrolling, then a few minutes later lost depth as well. 10 minutes later a loss of DSM came up on screen and then I think it rebooted and everything was good. Then throughout the day all these issues kept repeating (not in the same order). Also 1/2 hr later the entire screen started flickering. I was running the fishing mode which was 1/2 chart, 1/2 sonar at the time. The flickering would continue until the next time I received the "lost DSM" and then it would be ok for 5-10 minutes. Thinking the flickering may have been caused by low voltage I ran the motors with no effect. For the run home I switched to full chart screen and the flickering immediately stopped and did not return.
I had read a lot online about the "DSM300" that was manufactured in Mexico. So was not surprised when this all occurred. I pulled the Unit out and sure enough, Designed in "USA,Made in Mexico" It is a E63069, sn#05051502.
What are my options? Of course I have read that RM is replacing these with the CP370 and if that is possible that is what I prefer. I would be happy to return the unit for you to test/verify. I need to have the new unit installed by no later than the end of December. After reading all the issues about the DSM 300 I would not be open for a repair. Hopefully RM can replace this as they have been doing with the next model cp370. Thank you for your help and I look forward to hearing from you. Have a great day! I
I recently purchased a boat equipped with The following Raymarine electronics:
E140W Hybrid display
RS125 GPS antenna
E92143 4KW Radome
DSM300
Ray240 VHF
And I just installed a TM258 transducer to replace a P66 that the previous owner had knocked off.
On my short test rides after installing the TM258 everything ran fine. However on Sat I ran out 30 miles into Gulf of Mexico. Max depth 100'. Everything ran good until about 20 miles out, 70' of water. Then I first lost scrolling, then a few minutes later lost depth as well. 10 minutes later a loss of DSM came up on screen and then I think it rebooted and everything was good. Then throughout the day all these issues kept repeating (not in the same order). Also 1/2 hr later the entire screen started flickering. I was running the fishing mode which was 1/2 chart, 1/2 sonar at the time. The flickering would continue until the next time I received the "lost DSM" and then it would be ok for 5-10 minutes. Thinking the flickering may have been caused by low voltage I ran the motors with no effect. For the run home I switched to full chart screen and the flickering immediately stopped and did not return.
I had read a lot online about the "DSM300" that was manufactured in Mexico. So was not surprised when this all occurred. I pulled the Unit out and sure enough, Designed in "USA,Made in Mexico" It is a E63069, sn#05051502.
What are my options? Of course I have read that RM is replacing these with the CP370 and if that is possible that is what I prefer. I would be happy to return the unit for you to test/verify. I need to have the new unit installed by no later than the end of December. After reading all the issues about the DSM 300 I would not be open for a repair. Hopefully RM can replace this as they have been doing with the next model cp370. Thank you for your help and I look forward to hearing from you. Have a great day! I
↧
C120 Classic upgrade to C120 3rd generation
Hi have a C120 classic vintage 2004 which connects to a Raymarine dome radar, autohelm auto pilot and tridata instruments all vintage 2004. I was thinking of replacing the C120 with the newer C120 3rd generation to get a brighter display as well as some new features included with the 3rd generation.
My questions
would the new MFD be compatible with my existing connections as radar and autopilot ? Simply plug all existing cables into the new MFD.
Also could I interface the new MFD with a Quantum radom as a backup to my older radom either via a wire or wifi/blutooth?
The existing MFD is mounted is surface mounted would the new MFD fit into the existing cutout?
Thanks
Thanks
My questions
would the new MFD be compatible with my existing connections as radar and autopilot ? Simply plug all existing cables into the new MFD.
Also could I interface the new MFD with a Quantum radom as a backup to my older radom either via a wire or wifi/blutooth?
The existing MFD is mounted is surface mounted would the new MFD fit into the existing cutout?
Thanks
Thanks
↧
Replacement for ST 8002 autopilot control head
I have 2 ST 8002 auto pilot control heads and would like to upgrade to the modern version. What control heads will work with the existing auto pilot components..?
↧