Interfacing a Rockford Fosgate stereo receiver to an a/c/e/eS/gS-Series MFD
Chapter 22 - Audio Application of the LightHouse Release 17 Operation Instructions provides details of how compatible Rockford Fosgate stereo receivers may be interfaced to an a/c/e/eS/gS-Series MFD...
View ArticleUsing an instrument depth transducer with a fishfinder?
Instrument depth transducers are designed to exclusively to be interfaced to the DEPTH transducer terminals of the following: - an Depth instrument (ex. i40 Depth, i40 Bidata, i50 Depth, i50 Tridata,...
View ArticleWind transducer through iTC-5
My current system is as follows: ST60 Wind + Speed + Depth + Repeater + Wireless remote on ST1; ST1 into ST-STNG converter; Evolution autopilot and e125 on NG side, with ACU400 powering the NG circuit....
View ArticleRecommendations for system upgrade/update
Hello, I have a classic E80 that I would like to upgrade (I keep getting the dreaded DSM connection lost). It was installed in 2006 timeframe in a 2005 Silverton 35MY. It appears to be attached to a...
View ArticleSmart pilot S10
My autopilot says it is aSmart Pilot S10 but the book that came with it says SPX 10 what is the difference?
View ArticleFerrite Supression required for new ACU-200?
I'm upgrading my A/H from a Raymarine 150/400 to the Evolution 1 with the ACU-200. I notice there is a Ferrite Supression module on the power line? Do I need this for my new unit? Any harm in leaving...
View ArticleSeatalk2 to STng
I'm currently trying to straighten out some networking on a sailboat that has had several generations of electronics installed and I'd like to streamline and simplify the interfaces. At the end of...
View ArticleClik here to view.
Electronics Upgrade
On my Mainship 30 Pilot II Sedan I currently have a Raymarine c70 which I use for a chartplotter it uses a 125 GPS antenna, a RL70c which I use for my 24" Raymarine analog radar a ST60 Tridata with...
View ArticleImportance of maintaining separation of heading sensor from magnetics
Raymarine autopilots are designed to sense magnetic north and utilize magnetic heading data. In the case of Evolution autopilots, the magnetic north sensing component is the EV-1 Sensor Core. In the...
View ArticleACU-200 Drain Wire
My boat's bonding system connects to the DC ground at a busbar that is located within 12" of where I am planning to mount the ACU-200. Would it be acceptable to connected the drain wire from the...
View ArticleTransducer adapter
I have a P66 transducer with a 10 pin plug currently connected to a northstar 491. Is there an adapter or a way to modify this transducer cable/ connector so that I can connect this to my A67 MFD?
View ArticleWhat should I connect my mechanical linear drive's leads to?
The heavier gauge red and black leads of a Raymarine mechanical linear drive are its motor (power) leads. These leads will be connected to the autopilot course computer or Evolution ACU's MOTOR A / B...
View ArticleTransducer Capability
Installing a pair of eS128 MFDs on a center console with a 22 degree deadrise and a single outboard engine. Recently a RAYMARINE technician informed me that a CPT-S E70341 transducer would provide...
View ArticleClik here to view.
a/c/e/eS/gS-Series MFD with CHIRP/DownVision Transducer vs. CPT-S Transducer
Should a compatible CHIRP/DownVision transducer (i.e. CPT-100, CPT-110, CPT-120) be interfaced to an ax8 MFD, eSx8 MFD, or any model of a/c/e/eS/gS-Series MFD which has been interfaced to a CP100...
View ArticleST50 Speed instrument compatible with CruzPro SOG-1?
I'd like to avoid a paddlewheel sensor and so am considering using a CruzPro "SOG-1 paddlewheel converter" (http://cruzpro.com/sog1.html) to provide a speed signal to an ST50 Speed instrument, which...
View ArticleP70
Hi, I would like to replace my older control head st6002 with the p70. The st6002 Control head is on a pod mounted on the pedestal guard so I am trying to avoid running new cabling up the guard. Can I...
View ArticleTrip Log
I see how to reset the trip logs, but how do I restart the counter after it has been reset to zero? I'm using a e7D with updated software and Navionics charts. Thanks
View Articleschematic for sport pilot stalk arm
I have a Sport Pilot with the ribbon cable from the stalk arm to the drive unit is severed, the stalk arm itself was also busted by a repairman working on the boats throttle. I have a stalk arm given...
View ArticleUnable to view diagrams
I found a description of a system diagram that is very close to one I am trying to do, but I am unable to get the 3 diagrams in it to display. Any advice would be appreciated. It is in the FAQ...
View ArticleQuantum Radar power cord connection
I'm replacing a Nobeltec Radar with the Quantum Radar and I want to use the existing power cord. Where can I order an end connector (and the part #) to fit the Quantum Radar to attach to the end of the...
View Article