The information on the microtalk is not clear on whether it can be readily networked with the tack tick system. I purchased the cruising set a few years ago that included the T122 with wind, depth/speed displays and want to interface this with seatalk so I can read this information on my es7 chartplotter. I also have the EV100 in this set-up and autohelming on wind angle would be an extra bonus if possible.
↧
[CA11] Microtalk with Raymarine tacktick
↧
[CA11] ST70 multifunction instrument display won't sync with ST60+ AWI
ST70 is on a STNG network. St60+ is plugged into the STNG network with a seatalk adapter. Wind angle on AWI is correct but display on ST70 is 180 degrees off. By manually compensating the ST70 I can only get within 90 degrees of the AWI.
How do I get both instruments to display the same information?
How do I get both instruments to display the same information?
↧
↧
[CA11] upgrade from E120 to Axiom Pro will my older radar etc work
Hello,
I need to replace my E120. I would like to use an Axiom Pro RVX. I am hoping my older electronics will work so I can change items one at a time instead of all at once.
Connected devices:
B258 transduce to DSM 300
ST70 Auto Pilot
4 foot 4 kw HD Digital radar
SR100 SIRIUS weather system
125 GPS receiver
Can you tell me if these items will work with the Axiom Pro RVX.
If additional information is needed please let me know.
Thank you very much,
RD
I need to replace my E120. I would like to use an Axiom Pro RVX. I am hoping my older electronics will work so I can change items one at a time instead of all at once.
Connected devices:
B258 transduce to DSM 300
ST70 Auto Pilot
4 foot 4 kw HD Digital radar
SR100 SIRIUS weather system
125 GPS receiver
Can you tell me if these items will work with the Axiom Pro RVX.
If additional information is needed please let me know.
Thank you very much,
RD
↧
[CA11] AWA reported by MFD, MFID, or ST60 Graphic differs from ST60/ST60+ Wind Inst.
AWA reported by MFD, i70/i70S/ST70 MFID, or ST60/ST60+ Graphic differs from ST60/ST60+ Wind Instrument
When the subject symptom is reported, one should first verify that the ST60/ST60+ Wind instrument has been configured to display apparent wind data instead of true wind data (i.e. both devices have been configured to display wind of the same reference frame). If so and the symptom persists, then the ST60/ST60+ Wind Instrument's pointer would be deemed to be out of alignment or possibly to have failed, as the MFD, i70/i70S/ST70 MFID, or ST60/ST60+ Graphic devices are designed to simply repeat apparent wind data which the devices has received via its SeaTalkng / NMEA 2000 communications interface or its SeaTalk communications interface. The ST60/ST60+ Wind instrument has built-in self-test functions to aid fault diagnosis. Stage 3 of the self-test feature may be used to realign the pointer of the ST60/ST60+ Wind Instrument. To access self-test mode:
A. Press Key 1 and Key 4 together for 4 seconds.
B. When the unit beeps, immediately press Key 3 and Key 4 together momentarily. The unit will enter self-test stage 1. The unit should display S t followed by T1.
C. Press Key 1 and Key 2 together momentarily to progress to self-test stage 2. The pointer will rotate continuously.
D. When the pointer has completed at least one rotation, press Key 1 and Key 2 together momentarily to progress to self-test stage 3.
E. Self-test stage 3: This stage is to set up pointer offset and corrections. On entry the LCD will show T3 and then indicate the position to which the pointer should be positioned to adjust for pointer offset.
.....a. Momentary presses of Key 1 will rotate the pointer clockwise to align with the major graduations. Should there be any misalignment repeatedly press Key 3 for anti-clockwise or Key 4 for clockwise adjustment until correct alignment is obtained on all major graduations.
.....b. On completion of correction adjustments press Key 1 and Key 2 together momentarily to progress to self-test stage 4
F. To exit self-test and store pointer corrections press Key 1 and Key 2 together for 2 seconds. If storage of pointer corrections is not required press Key 1 and Key 2 together momentarily to exit.
RAYFAQ#
When the subject symptom is reported, one should first verify that the ST60/ST60+ Wind instrument has been configured to display apparent wind data instead of true wind data (i.e. both devices have been configured to display wind of the same reference frame). If so and the symptom persists, then the ST60/ST60+ Wind Instrument's pointer would be deemed to be out of alignment or possibly to have failed, as the MFD, i70/i70S/ST70 MFID, or ST60/ST60+ Graphic devices are designed to simply repeat apparent wind data which the devices has received via its SeaTalkng / NMEA 2000 communications interface or its SeaTalk communications interface. The ST60/ST60+ Wind instrument has built-in self-test functions to aid fault diagnosis. Stage 3 of the self-test feature may be used to realign the pointer of the ST60/ST60+ Wind Instrument. To access self-test mode:
A. Press Key 1 and Key 4 together for 4 seconds.
B. When the unit beeps, immediately press Key 3 and Key 4 together momentarily. The unit will enter self-test stage 1. The unit should display S t followed by T1.
C. Press Key 1 and Key 2 together momentarily to progress to self-test stage 2. The pointer will rotate continuously.
D. When the pointer has completed at least one rotation, press Key 1 and Key 2 together momentarily to progress to self-test stage 3.
E. Self-test stage 3: This stage is to set up pointer offset and corrections. On entry the LCD will show T3 and then indicate the position to which the pointer should be positioned to adjust for pointer offset.
.....a. Momentary presses of Key 1 will rotate the pointer clockwise to align with the major graduations. Should there be any misalignment repeatedly press Key 3 for anti-clockwise or Key 4 for clockwise adjustment until correct alignment is obtained on all major graduations.
.....b. On completion of correction adjustments press Key 1 and Key 2 together momentarily to progress to self-test stage 4
F. To exit self-test and store pointer corrections press Key 1 and Key 2 together for 2 seconds. If storage of pointer corrections is not required press Key 1 and Key 2 together momentarily to exit.
RAYFAQ#
↧
[TG11] Axiom crash on upgrade and reset.
I've got a Raymarine Axiom 9 which has been working very well.
Back in April this year I updated to v3.4.66 with success via a SD Card.
Since then I have not been able to update to any of the new versions including the one just released v3.7.70.
I have tried the following since April to resolve this issue. Here are some things I and tried and observed.
1. Tried a Settings RESET - The Unit asked for Yes or No. When I hit YES it says rebooting and the screen goes black and it never comes back. 1 hour say, I had to turn electronics switch off and on and it comes back.
2. Tried a Factory RESET - The Unit asked for Yes or No. When I hit YES it says rebooting and the screen goes black and it never comes back. 1 hour say, I had to turn electronics switch off and on and it comes back.
3. Software Update. It finds the update for the Axiom and after I select the update it reboots and never comes back. When I power off and on at circuit is says Software Update Failed. No details as to why. I have crash logs so I know it is crashing on 1, 2 and 3.
4. Disconnected the transducers, disabled all transducers and tried 1,2,3 - Same results.
5. Disconnected nmea BUS and tried 1,2,3 - Same results
6. WIFI download update - same as 3.
I have managed to get the systemlog off the unit and had a look through it. The log has the following which doesn't look good. Maybe just a distraction.
Should I post the complete log? It is
10-26 10:24:51.310 748 1069 E ProcessMonitor: Processor Monitor timeout detected
10-26 10:24:51.312 748 1069 E MFDApplication: *----------------------------------------------------------------------------
10-26 10:24:51.312 748 1069 E MFDApplication: * Mutex Information
10-26 10:24:51.312 748 1069 E MFDApplication: *
10-26 10:24:51.312 748 1069 E MFDApplication: * OSSMutexId Name Thread OSSTaskId LWP Lck Cnt Nusers
10-26 10:24:51.312 748 1069 E MFDApplication: * ---------- ----------------------------------- ----------------------------------- ---------- ---------- --- --- ------
10-26 10:24:51.312 748 1069 E MFDApplication: * 0xB7BF5594 TCPSocketServer.cpp:46 LNetNavigationServer.cpp:54 0xB7BF55DC 1309 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BF4C5C TCPSocketServer.cpp:46 LNetTrackServer.cpp:44 0xB7BF4CAC 1307 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BD853C TCPSocketServer.cpp:46 LNetWaypointServer.cpp:51 0xB7BD8590 1305 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BD1264 TCPSocketServer.cpp:46 CLNetDataBaseServer::RxConnectionTask 0xB7BD12C0 1302 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BBC79C TCPSocketServer.cpp:46 LNetDiagnosticsServer.cpp:78 0xB7BBC5D4 1290 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: *
10-26 10:24:51.313 748 1069 E MFDApplication: * Possible Deadlocks:-
10-26 10:24:51.313 748 1069 F MFDApplication: Watchdog timeout detected
Tombstone written to: /data/tombstones/tombstone_00
Does anyone have any suggestions? Should I log a ticket with Raymarine?
Cheers,
Ken
Back in April this year I updated to v3.4.66 with success via a SD Card.
Since then I have not been able to update to any of the new versions including the one just released v3.7.70.
I have tried the following since April to resolve this issue. Here are some things I and tried and observed.
1. Tried a Settings RESET - The Unit asked for Yes or No. When I hit YES it says rebooting and the screen goes black and it never comes back. 1 hour say, I had to turn electronics switch off and on and it comes back.
2. Tried a Factory RESET - The Unit asked for Yes or No. When I hit YES it says rebooting and the screen goes black and it never comes back. 1 hour say, I had to turn electronics switch off and on and it comes back.
3. Software Update. It finds the update for the Axiom and after I select the update it reboots and never comes back. When I power off and on at circuit is says Software Update Failed. No details as to why. I have crash logs so I know it is crashing on 1, 2 and 3.
4. Disconnected the transducers, disabled all transducers and tried 1,2,3 - Same results.
5. Disconnected nmea BUS and tried 1,2,3 - Same results
6. WIFI download update - same as 3.
I have managed to get the systemlog off the unit and had a look through it. The log has the following which doesn't look good. Maybe just a distraction.
Should I post the complete log? It is
10-26 10:24:51.310 748 1069 E ProcessMonitor: Processor Monitor timeout detected
10-26 10:24:51.312 748 1069 E MFDApplication: *----------------------------------------------------------------------------
10-26 10:24:51.312 748 1069 E MFDApplication: * Mutex Information
10-26 10:24:51.312 748 1069 E MFDApplication: *
10-26 10:24:51.312 748 1069 E MFDApplication: * OSSMutexId Name Thread OSSTaskId LWP Lck Cnt Nusers
10-26 10:24:51.312 748 1069 E MFDApplication: * ---------- ----------------------------------- ----------------------------------- ---------- ---------- --- --- ------
10-26 10:24:51.312 748 1069 E MFDApplication: * 0xB7BF5594 TCPSocketServer.cpp:46 LNetNavigationServer.cpp:54 0xB7BF55DC 1309 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BF4C5C TCPSocketServer.cpp:46 LNetTrackServer.cpp:44 0xB7BF4CAC 1307 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BD853C TCPSocketServer.cpp:46 LNetWaypointServer.cpp:51 0xB7BD8590 1305 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BD1264 TCPSocketServer.cpp:46 CLNetDataBaseServer::RxConnectionTask 0xB7BD12C0 1302 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: * 0xB7BBC79C TCPSocketServer.cpp:46 LNetDiagnosticsServer.cpp:78 0xB7BBC5D4 1290 1 1 0
10-26 10:24:51.313 748 1069 E MFDApplication: *
10-26 10:24:51.313 748 1069 E MFDApplication: * Possible Deadlocks:-
10-26 10:24:51.313 748 1069 F MFDApplication: Watchdog timeout detected
Tombstone written to: /data/tombstones/tombstone_00
Does anyone have any suggestions? Should I log a ticket with Raymarine?
Cheers,
Ken
↧
↧
[TG11] p70s & i70s - wind
Hello,
I have a issue where the wind on the i70s and the p70s is shown as coming from different directions.
System hardware:
EV400 + p70s
Sail Pack + DST800 + iTC5 + i70s + wind vane/anemometer
There is also a Axiom Pro running the latest version of LH3
Tried so far:
Set both to display apparent wind.
Observations:
The "dumb" wind vane at the top of the mast that is not connected to anything appears to align with the i70s, its the p70s that is considerably different.
I calibrated the EV400 when installed, it was several months later that the Sail Pack was installed, and the sail pack was then calibrated (speed, wind, temperature were all calibrated).
Q: Beyond how to fix this, I would like to know where the wind calibration data is stored? I assume on the iTC5.
wind1.jpg (Size: 197.75 KB / Downloads: 1)
wind2.jpg (Size: 169.53 KB / Downloads: 1)
I have a issue where the wind on the i70s and the p70s is shown as coming from different directions.
System hardware:
EV400 + p70s
Sail Pack + DST800 + iTC5 + i70s + wind vane/anemometer
There is also a Axiom Pro running the latest version of LH3
Tried so far:
Set both to display apparent wind.
Observations:
The "dumb" wind vane at the top of the mast that is not connected to anything appears to align with the i70s, its the p70s that is considerably different.
I calibrated the EV400 when installed, it was several months later that the Sail Pack was installed, and the sail pack was then calibrated (speed, wind, temperature were all calibrated).
Q: Beyond how to fix this, I would like to know where the wind calibration data is stored? I assume on the iTC5.


↧
[CA11] Proper placement of ferrites
I could not find the documentation of exactly where to place the ferrites that came with my EVO wheel pilot parts and instruments.
↧
[CA11] B744V compatibility question...
Hi. I'm looking to buy a triducer for my dsm300 and raymarine instruments.
The raymarine website says I need a B744V. But I heard there are two types of the b744v, one which is compatible with the dsm300, and one which isn't? Which is the E66061? If not this, what is the part number for the transducer I need? Cheers
The raymarine website says I need a B744V. But I heard there are two types of the b744v, one which is compatible with the dsm300, and one which isn't? Which is the E66061? If not this, what is the part number for the transducer I need? Cheers
↧
[CA11] ST60+ POwer but no speed or direction
Hi,
I have a 2009 vintage ST60+ wind instrument. It had been working fine. It powers up but shows nothing for wind speed or direction. Arrow just points straight up and no wind reading. Instrument at top of mast is spinning and pointing fine. Any thoughts?
Thanks,
Russ
I have a 2009 vintage ST60+ wind instrument. It had been working fine. It powers up but shows nothing for wind speed or direction. Arrow just points straight up and no wind reading. Instrument at top of mast is spinning and pointing fine. Any thoughts?
Thanks,
Russ
↧
↧
[CA11] eS97 and AIS target tracking
The sailboat has the eS97 with Lighthouse 2 software installed. The boat also has an AIS receiver connected to the NMEA2000/Seatalkng
buss. I would like to understand if you can selectively remove one of the AIS targets so that it does not cause an alarm condition if this target is following you. This target is a friends boat that is traveling as part of a group going south. All other target should stay active and cause alarms when you are on watch at night. The crew is sleeping and these alarms from the boats that are in the traveling group cause them to wake up.
Thanks
George
buss. I would like to understand if you can selectively remove one of the AIS targets so that it does not cause an alarm condition if this target is following you. This target is a friends boat that is traveling as part of a group going south. All other target should stay active and cause alarms when you are on watch at night. The crew is sleeping and these alarms from the boats that are in the traveling group cause them to wake up.
Thanks
George
↧
[CA11] Raymarine UAV drone app live view cannot be recorded from Axiom Screen?
Hi, I finally bought my Mavic Pro drone (open box with discount-2 cables missing) and tested the Axiom UAV drone app a few weeks ago. I always use my IOS built in screen recorder to record Axiom screen with Rayview app and (iPhone connected to Axiom wifi) so I tried to record the Axiom screen with Mavic Pro drone live view that was reflected in the Axiom screen. But, Drone live view was NOT shown on my iPhone screen even though it was shown on the Axiom 9" screen.
So. I just use my iphone pic/video app to record the Axiom screen. But, I had 2 problems:
(1) iphone was interfereing the Axiom so iphone video has 2 black lines,
(2) sunglare.
2 Questions for Raymarine engineers:
(1) what can I do on my iphone or Axiom to stop the interference?
(2) Can you fix it so that Axiom screen can be seen in Rayview app on iphone?
Thanks.
So. I just use my iphone pic/video app to record the Axiom screen. But, I had 2 problems:
(1) iphone was interfereing the Axiom so iphone video has 2 black lines,
(2) sunglare.
2 Questions for Raymarine engineers:
(1) what can I do on my iphone or Axiom to stop the interference?
(2) Can you fix it so that Axiom screen can be seen in Rayview app on iphone?
Thanks.
↧
[CA11] Lighthouse 3 v3.7.70 Axiom update problem
Good morning. I attempted to update my Axiom 9 from v3.6.32 to v3.7.70. The process ran updated the AIS 700, ran a 10 minute clock, then locked at 0m 0s. Screen photo attached. I was not able find troubleshooting recommendations using search. Thanks for any help.
Thanks, Rick
IMG_1649.JPG (Size: 261.24 KB / Downloads: 2)
Thanks, Rick

↧
[CA11] What is the difference
I have an older Dragonfly that I bought when they first showed up on the market. I was curious to what the difference is from that $700 I paid for it to those on the market to day for half that price.
↧
↧
[CA11] Replacement for b744
Is there a direct replacenent for a B744 through hull transducer....for an Axiom 9 “all in one” equivalent. 2” diamater...without resizing the [censored]? Old unit A65 and DSM25
↧
[CA11] gps data conversion, nmea0183 to seatalk to seatalk ng to neme 2000
Hi everyone,
my boat has a head instruments based on an old sea talk raymarine system with a st60multi and a st40. I upgrade in the last years with an evolution autopilot and a garmin gnx 120 masthead display.
I used to convert the gps nmea0183 data from my old garmin gps 128 to the sea talk network with the st60multi. Also the autopilot recognize the gps data in his seatalkng network, but i cannot read the gps sentences in the garmin nmea2000 network.
Is there a problem in the translation of the gps data or in the conversion?
Thank you,
Simone from Italy
my boat has a head instruments based on an old sea talk raymarine system with a st60multi and a st40. I upgrade in the last years with an evolution autopilot and a garmin gnx 120 masthead display.
I used to convert the gps nmea0183 data from my old garmin gps 128 to the sea talk network with the st60multi. Also the autopilot recognize the gps data in his seatalkng network, but i cannot read the gps sentences in the garmin nmea2000 network.
Is there a problem in the translation of the gps data or in the conversion?
Thank you,
Simone from Italy
↧
[CA11] A97 MFD not showing AIS targets
Hi
I have just installed a A97 MFD. I have connected a Matsutec AIS via nema on port No 2. I have set Baud rate to 38400 in MFD.
MFD shows AIS icon on home screen as "Silent" even if I turn off Silent mode. The MFD alarms for AIS close targets, in line with AIS.
No AIS targets are shown on MFD screen, but alarming for targets correctly.
How do I get AIS targets to show on MFD ? I take it the silent mode is changeable and should show on home screen.
Any help offered much appricated.
Cheers
I have just installed a A97 MFD. I have connected a Matsutec AIS via nema on port No 2. I have set Baud rate to 38400 in MFD.
MFD shows AIS icon on home screen as "Silent" even if I turn off Silent mode. The MFD alarms for AIS close targets, in line with AIS.
No AIS targets are shown on MFD screen, but alarming for targets correctly.
How do I get AIS targets to show on MFD ? I take it the silent mode is changeable and should show on home screen.
Any help offered much appricated.
Cheers
↧
[CA11] Requirements for HD Radome on E120
Hi,
The RD424 E52067 on my boat has become intermittent. Sometimes it fills the display with solid amber return, if gain turned way down some echos are displayed (but not all), then it will eventually return to normal operation and I have to readjust the gain. Other times it stops all display and I need to power down the scanner and power it on again to recover. I am thinking of replacing the scanner with a refurbished 24" HD Color Radome E92143R on sale now. I believe this is compatible with my E120 which is running SW v5.69.
I also have a DSM30 which would be using the Seatalk HS connection on the E120 so I will need to add a HS5 switch to connect a digital Radome.
Questions:
1. Is the E92143R compatible with my E120?
2. I would likely mount the HS5 next to the DSM30. What cable is required to connect them?
3. For the E120 to HS5 connection, I could either run a new cable (maybe 8' or so?) or add an adapter to the cable currently plugged into the DSM30. Suggestions?
4. Please confirm for the Radome cable I would use "Radar Cable (RayNet)" such as A80228 or A80229 depending on required length for power and HS5 connection.
5. Please confirm that the E92143R is the same mounting as the RD424.
Thank you!
Howard
The RD424 E52067 on my boat has become intermittent. Sometimes it fills the display with solid amber return, if gain turned way down some echos are displayed (but not all), then it will eventually return to normal operation and I have to readjust the gain. Other times it stops all display and I need to power down the scanner and power it on again to recover. I am thinking of replacing the scanner with a refurbished 24" HD Color Radome E92143R on sale now. I believe this is compatible with my E120 which is running SW v5.69.
I also have a DSM30 which would be using the Seatalk HS connection on the E120 so I will need to add a HS5 switch to connect a digital Radome.
Questions:
1. Is the E92143R compatible with my E120?
2. I would likely mount the HS5 next to the DSM30. What cable is required to connect them?
3. For the E120 to HS5 connection, I could either run a new cable (maybe 8' or so?) or add an adapter to the cable currently plugged into the DSM30. Suggestions?
4. Please confirm for the Radome cable I would use "Radar Cable (RayNet)" such as A80228 or A80229 depending on required length for power and HS5 connection.
5. Please confirm that the E92143R is the same mounting as the RD424.
Thank you!
Howard
↧
↧
[CA11] Replacing L760
Hello,
I currently have L760 and Rl70c units installed as my current setup. I was looking to upgrade one of these to a newer 9 inch unit, possibly an A97. I'd assume it would be easier to replace the L760 and leave the Rl70c as I am pretty content with this setup for its radar. My main concern in upgrading besides the larger screen is the fishfinder capabilites and to a lesser degree the Chartplotter aspect. Would an A97 unit be compatible with my current 50/200 transducer as well as the Rl70c unit? What other considerations would I have to be concerned with if I went this route?
Thanks
I currently have L760 and Rl70c units installed as my current setup. I was looking to upgrade one of these to a newer 9 inch unit, possibly an A97. I'd assume it would be easier to replace the L760 and leave the Rl70c as I am pretty content with this setup for its radar. My main concern in upgrading besides the larger screen is the fishfinder capabilites and to a lesser degree the Chartplotter aspect. Would an A97 unit be compatible with my current 50/200 transducer as well as the Rl70c unit? What other considerations would I have to be concerned with if I went this route?
Thanks
↧
How can I lower the minimum height of 33 feet in the UAV app?
Hi,
How can I lower the minimum height of 33 feet in the Initial height after Take-off in the UAV app?
your app would not allow me to decrease it under 33 feet. This is very inconvenient considering Mavic Pro initial height after take off is ONLY 3 feet.
I like to have it hover at 10 feet-12 feet after Initial take off or fish-on so my boat in the drone video can look a lot Bigger than it looks.
33 feet minimum or 3+ stories high is simply too tall.
It does allow me to increase the height to more than 33 feet.
How can I lower the minimum height of 33 feet in the Initial height after Take-off in the UAV app?
your app would not allow me to decrease it under 33 feet. This is very inconvenient considering Mavic Pro initial height after take off is ONLY 3 feet.
I like to have it hover at 10 feet-12 feet after Initial take off or fish-on so my boat in the drone video can look a lot Bigger than it looks.
33 feet minimum or 3+ stories high is simply too tall.
It does allow me to increase the height to more than 33 feet.
↧
[LW11] axiom fuel data
I'm using an Axiom 12 and have somewhat successfully connected to a Suzuki Df 140 for the purpose of receiving fuel data, I found the well hidden engine data option menu's and am happy with the result ie: fuel tank level, litres per 100 klm.
So my question is, can I populate that side slide out menu with this data?
I'm running the latest LH3 software
Thanks Mark
So my question is, can I populate that side slide out menu with this data?
I'm running the latest LH3 software
Thanks Mark
↧