Old rudder indicator with Evolution Course Computer
I currently use an S1 SmartPilot (E15016) with two rudder indicators (A22008) attached. If I upgrade to a new Evolution style course computer will my existing rudder indicators still work?
View ArticleAIS 100 default condition
I am about to fit an AIS 650 to my boat utilising an AIS100 splitter. If the AIS100 has no power on it (AIS system switched off), will the VHF tranceiver still be connected to the antenna? i.e. the...
View ArticleES128 and ES127 Not Displaying Engine Data on IPS Boat
I purchased a 2 year old 42' Regal Sport Coupe that only had a basic third party MFD as it was a lake boat. Now in the Northeast I had all the third party electronics removed and replaced with...
View ArticleWill the AIS100 support VHF radio transmission in the event of power loss
The function of the AIS100 Class B AIS Antenna Splitter is ensure that RF energy from only one device (i.e. the AIS Class B transceiver or VHF radio) is being broadcast at any time. This function is...
View ArticleClik here to view.
Compass Safe Distances for Raymarine eS-Series MFDs
Compass Safe Distances are the minimum distances that product may be installed within proximity to a compass without affecting the deviation sensed by the compass. Should a product be installed closer...
View ArticleE120 Classic Interface to AIS 650
I understand that to connect an AIS 650 to an E120 Classic (w/ SW V5.69) I must use the NMEA 0183 interface (38.4k between the E120 and AIS and 4.8k between the AIS and my VHF [Ray215]). I also have a...
View ArticleData from EV-1
The description of the EV-1 says it's a 9 axis sensor. But in the list of NEMA 2000 sentences the manual says it supports Rudder Angle and Vessel Heading are the only two that seem to have anything to...
View Articlei60 in old ST60 Flushmount cut out?
My flush mounted ST60 died and I am replacing it with a new i60. The ST60 was installed in the bulkhead and being flush mount, has a square cut-out that is not compatible with the standard i60. Is...
View ArticlePower for AP and MFD
Are there advantages and disadvantages to powering the autopilot (EV-100) and MFD (e7D) from the same branch circuit, or from separate circuits? OTOH, it makes sense to me to have them together, so...
View ArticleAIS650
Can the software update for the AIS650 be on the same SD card as the software update for the e127 that is connected to it?
View Articlee97 & e125 V16.47 SW Update Failed
I have my e97 and e125 networked with Seatalk HS with the e97 as the master and a WiFi connection. Previously SW V15.59 was installed on both units. I went online and looked for the latest SW update...
View Articlee7D Multifunction Display
e7D Multifunction Display have pinch to zoom? Thank you Sergio
View ArticleConverting from .usr to .gpx
I used GPS Babel to convert my lowrance USR files to GPX but when I import them only some of the waypoints transfer and I get a import failed messaged. - Is there a way to edit the file to make sure it...
View ArticleProfile
Setting up new profile. Just getting my feet wet in this new forum. I can't fine the loc. to put what state I am from in the profile. (Additional info) I ended up putting it in the Bio. If you view...
View ArticleInstalling back bone
I have currently a C125 hooked into a DSM300 and a B60 20 degree transducer, also a CP100 hooked to a CPT-100 transducer, RD418HD, HS5 hooking them together ( I have one connector still open for the...
View Article.FSH waypointss transfer to new a series
I have the waypoints I took off a C120 Classic. They are in a .fsh file format. Can I just copy them onto a micro SD card and put them in the new a9, or do I need to do something else? I have not found...
View ArticleCables ?
I am connecting my digital radar dome to my new C95 MDF. My previous MDF was a E80 with a RJ45 connection. What cable do I need to connect the radar to the C95? Thanks, Phil..
View ArticleBennett Trim Tab interface
What do I need to connect Bennett nema 2000 interface with Raymarine E125 to display trim position.
View ArticleOhming masthead
I read and followed the FAQ for the masthead wind sensor. It appears that the sensor is out of spec. The power supply, at the junction box near the mast, reads 7.94V. Both position sensors are in the...
View ArticleNew setup
I have a 26' Olympic with a 12 degree hull and I want to install a new fish finder so I decided on the A128 E70237-NAG MFD. I normally fish deep salt water from 10' to 1000' for bottom fish and also...
View Article