CPT-100/CPT-60/CPT-DV/CPT-DVS on vessel fitted with another transom transducer
As most vessels are fitted with a single transducer, Raymarine has not officially tested the CPT-100/CPT-60/CPT-DV/CPT-DVS alongside other transom mounted transducers and has correspondingly not...
View ArticleTemperature Readout ST-60 Speed
About mid summer last year, I started to get erroneous temperature readouts from the ST-60 Speed Log. All other functions work fine. There is a temperature presented, usually 2 degrees centigrade, but...
View ArticleE120 Classic N2K GND10 gWind
I have an E120 Classic networked to a Pathfiner MFD at the nav station. On the Raymarine networks an analog radar and DSM30 and GPS, ST290 Data modual. I have an N2K backbone connected to the e120 NG...
View ArticleClik here to view.
Significant error in temperature reported by instrument
Incorrect temperature values reported by an instrument may result from any of the following: - Temperature offset not configured - Thermistor failure - Failure of Temperature sensing circuitry of...
View ArticleST50+ Wind factory reset
Good morning. Last week I successfully repaired my ST50+ Wind (without schematics!); there was a faulty semiconductor on the anemometer board in the masthead transducer and also a faulty transistor in...
View ArticleTransducer location
Where's the best place to mount a transducer on a 37' Searay Sundancer with 2 straight inboards? I know in general they should be mounted before the props so there's no problems with the readings. But...
View ArticlePC support for viewing quantum radar data
Are there any Window programs and network configurations that will allow for viewing radar data from the Quantum Radar units on a PC either via a wired or a WiFi connection?
View ArticleST 40 be used to supply info to the autopilot?
Good Day I have a customer with the following question: I currently have a Raymarine ST 40 Wind Instrument and a Standard Horizon CP 180i chartplotter. can the ST 40 be used to supply info to the...
View ArticleClik here to view.
Recommended locations for in-hull and thru-hull transducers
It is recommended that the transducer's installation manual be the primary reference for transducers to be installed onboard one's boat. Transducer installation location is critical to maximizing the...
View ArticleITC-5 with a97
I'd like to know if an a97 MFD can calibrate an ITC-5, or must I have an i70 connected to calibrate it?
View ArticleIs is possible to calibrate an instrument transducer via an...
It is not possible for an a/c/e/eS/gS Series MFD (or earlier MFD designs) to calibrate transducers which have been interfaced to an iTC-5, ST70/ST290 instrument pod, or instrument display. Instrument...
View ArticleMic only available?
My boat came with the RAY215 DSC But no mic. Can I still buy something compatible? Thanks, Jim
View ArticleCan I integrate Ray 260 VHF/AIS with SLRC70RC chart plotter
I would like to add AIS capability to my boat. I am considering upgrading my VHF radio with a Raymarine Ray 260 with integrated AIS. I have a SLRC70RC PLUS chart plotter. Can I interface the AIS...
View ArticleHonda to c95 mfd set up
I am looking for part numbers to set up my 2007 honda 225 with my c95 mfd for engine data only. No auto pilot. Currently have my sonar and radar connected directly to the mfd and no seatalk network has...
View ArticleClik here to view.
DST-800 Installation
Having problems getting a dst800 to seat in the thru hull with valve included with the transducer. I am using yellow o-ring but transducer is very difficult to tighten and will not seat to the bottom...
View ArticleEV-1 Linearization Problems
I also have a problem with linearizing my EV-1. I have continued to run the boat at 3 to 15 knots so many times, I've burned over 40 gals. of fuel. I noticed that Steve from Raymarine says to run at...
View Articlei40 Depth and Speed - "extension" cable.
I'd like to add an i40 Speed and Depth display to my little sailboat. She came with an AirMar B744. I have confirmed that the temperature and speed sender is OK, and I'm hoping the piezo depth...
View ArticleWhat should the drain leads from my marine electronics be connected to?
Should the vessel be equipped with a bonding plate and bonding cable, then the drain leads should be connected to the vessel's bonding cable. Should the vessel not be equipped with a bonding cable and...
View ArticleTesting an a/c/e/eS-Series MFD's NMEA 0183 ports
When troubleshooting a NMEA 0183 communications problem between an a/c/e/eS/gS-Series MFD and another device having a NMEA 0183 interface, a simple test with a analog voltmeter is often used to test...
View Article