Raystar 130 to E120
I am installing a Raystar 130 GPS antenna to seatalk and a E120. I am not sure where the three cables plug into the Seatalk converter base.
View ArticleCannot go to cursor, or follow route
Have just installed a new Ray Type 2 Hydraulic pump. After bleeding the system and calibrating the rudder - the autopilot will lock onto and keep a course in "auto" mode will accurately steer the boat...
View ArticleClik here to view.
Changing the splash screen of an a/c/e/eS/gS-Series MFD
OEM / User Splash Screen In line with using Lighthouse Version 6 (or above) software, Raymarine is pleased to announce the option of adding an OEM / User splash screen to the power-on sequence for the...
View ArticleClik here to view.
Resetting / Removing the OEM / User splash screen of an a/c/e/eS/gS-Series MFD
Resetting / Removing OEM / User Splash Screen In line with using Lighthouse Version 6 (or above) software, Raymarine provided an option of adding an OEM / User splash screen to the power-on sequence...
View Article2nd Station upgrade issue
I upgraded my Ray60 to version 1.35. I just purchased an new Ray Mic 2nd station and tried to get it to upgrade as well by putting the radio in to the boot loader mode and 2nd station mic into...
View ArticleC80 Chartplotter slow down
I recently updated my C80 Chartplotter with the most recent charts from Navionics. After doing so I noticed a significant delay in moving around the chart using the softkeys, such as when I wanted to...
View ArticleICOM M506 AIS
Hello, I have an Icom M506 VHF radio with AIS attached to my network via NMEA-2000. The radio picks up GPS signal from the network, displays AIS on the radio display but I can't get it to display on my...
View ArticleVoltage monitoring
Trying to monitor input voltage to my E7d as my engines are not NMEA networked.
View ArticleDTE Data
Hello support team. My E95 is managing my fuel consumption and he is able to display the DTE (Distance to Empty) on any screen on the unit. Is there a way to transmit the values related to fuel...
View ArticleEvoluion will not working properly
I recently updated the software for my electronics which included the AP. The instructions included the need to recalibrate the AP so I went ahead and did the dock side wizard and everything appeared...
View Articlea75 possibly causing nmea2000 bus crash
Not sure if this belongs on the MFD or instrument forum. Four years ago I installed a system that has the following; Furuno NavNet3D display, Simrad AC42/AP28 autopilot, WSO100 weather station, DST800...
View ArticleClik here to view.
Dual Station Depth Speed Requirement
I have a requirement to display vessel speed and depth on both the upper helm (bridge) and lower helm positions (dual station). I think the i40 Bidata displays fit the bill if I use the all-in-one...
View ArticleSirius 150 Weather receiver, GPS & Antenna
We are looking to acquire and integrate a Sirius 150 weather receiver. Q1. The documentation says a GPS is required. If I am providing GPS to the e165 MFD via NMEA 0183, will that satisfy the...
View ArticleRay215 Squelch
My squelch cannot be turned low enough. At the minimum the display shows two bars and nothing comes through. It cannot be turned down to a point where the radio makes static like it did when it was...
View ArticleDrive Type Selection
I am recommissioning an SPX 30 autopilot with ST70 controller after updating the AP software. The boat displaces approximately 36000 pounds, has a Simrad RPU160 reversible pump (160-550cc) being used...
View ArticleCp470
Will the cp470 chirp sonar work with the newer c series mfd. Also can the c series be networked with a e165 mfd. Thanks
View ArticleRC435 Chartplotter Shows Incorrect Ship Position
My friend has a RC435 Chartplotter. It seems to be working fine except the ship position is off by approx. 100-200 feet. All of the options in the menu seem to be fine. I have set the SD card and...
View ArticleAIS proAIS download
I am trying to check the operating status of my 650 via a windows 10 laptop. I have downloaded the USB drivers (at least the software says " ProAIS USB Driver v2.00 has been installed on your...
View ArticleST8002 with an E127
Two questions, I installed a new e127 on a new to me 2007 Legacy 32 Down-east Express. I updated the Lighthouse software and created a route using the auto routing. I opened up the route and hit follow...
View Article