Speed/Temp transducer
I did a check following your guide on my paddle wheel and had 4.6V on and off as we slowly turned the wheel. However we get 0.0 Kts readings on the multi display ST50. How can I test the ST50 or is the...
View Articleradar not fonctionning correctly
I have a new radar RD418D plug on a ES97 MFD. It work fine for a month, now nothing appear on the MFD radar screen except when i put the GAIN at 80 or above then the screen goes all blue and yellow. I...
View ArticleClik here to view.
Connecting Multiple NMEA 0183 Devices
I have a question concerning NMEA 0183 connection to an e127/e125 MFD. I am replacing my AIS650 Class B AIS with a non-Raymarine Class A AIS using NMEA 0183 ports. My current system consists of 2 MFDs,...
View Articlee7d not retaining bearing mode configuration setting
My system: E7D Color HD radar SPX-5 pilot AIS 650 In system preferences, i set it to magnetic. When next powered up it had switched back to true. Has done this twice. Why?
View ArticleE7D - displaying AIS targets within Chart application
My system: E7D Hd color radar SPX-5 pilot AIS650 When using split screen of chart and radar, AIS targets show up on radar. Can be switched to chart pane?
View ArticleE7D - selecting the active pane
My system: E7D HD color radar SPX-5 pilot AIS 650 When in split screen of chart and radar, how do you switch to one or the other being active using only buttons and knobs. No touch screen. My...
View ArticleClik here to view.
CP470 bottom tracking Issue
I've got an odd problem with my fish finder that I can't figure out, might just be a setting I'm missing or maybe something technically wrong it, tried everything I can think of. See attached picture....
View ArticleRay49 VHF
I have a Ray 49 VHf radio which stopped transmitting and receiving. It does turn on and i do get the TX in the upper left corner with shows it transmitting but i get no response . Id like to replace it...
View ArticleSoftware update
You always state that the first problem solving step is to be sure you're at the latest Lighthouse software update. From what i can discern, ver.17 has no features that I'm interested in. Hopefully,...
View ArticleNo satellite data and STLK Fail message on auto pilot
Good morning, A couple of weeks ago, I lost satellite data on my C80 and the message STLK fail appeared on my Auto Pilot (ST6001). I contacted Raymarine support and was told to change the battery and...
View ArticleSR100 connection to Es75
I just purchased a new Es75 MFD and have a SR100 that I would like to connect. I have Seatalk instruments and interfaced them with a SeaTalk one to SeaTalkng converter. The SR100 is ST hs. What is...
View ArticleRadar
I have a C80 radar that I can't switch on. I am unable to see the usual Radar TX/Stdby or Scanner On/Off buttons as they are 'greyed out'. How do I get them back, so I can switch the radar back on?...
View ArticleE120 digital radome addition
The E120 installed in a 2009 boat never had radar, only DSM300 sonar and GPS (presumably RS125). Am I correct that a RD418D or RD418HD digital radome can be installed with the addition of a Seatalk HS...
View ArticleE120 upgrade
As I glanced at the flat rate repair schedule I see that the E120 is not listed for repair. What upgrade model would cover the existing cutout? What 18" radome is recommended? Is a Seatalk HS switch...
View Articlereplacing the radome enclosure
My 18" digital radar scanner had an unfortunate encounter with a bridge. the plastic case was broken, but the internal parts were not damaged. The unit still works correctly. I repaired the case, but...
View ArticleConversion from Simrad to Raymarine
I currently have an older Simrad AP11 autopilot on a hydraulically steered inboard. The controller is getting hard to read so I am wondering if I could change out the electronics to a Raymarine unit...
View ArticleAuto pilot not following route!
After setting up a route with my new "Auto Routing" feature I am having a problem instructing my "Auto Pilot" to lock onto the route. Every time I tell it to "Follow Route" it wants to turn 180...
View Articleconnecting analog cams to an e78
HI, I would like some help in connecting an set of analog cams to my new e78 display. I have the e78, set up and running, and now just got the cable to connect to my cam. Once I connect, how do I: 1-...
View ArticleClik here to view.
new cp370
hello swoped out a failing dsm300 for cp370. system has e140w touch screens. the cp370 was an easy plug in install and works fine in manual mode but not in auto. i have updated the software on the...
View Article