[CA] Equipment Upgrades
I have the following on my boat and would like to replace the chart plotter and possibly the radar. Current Equipt. RL70C Chartplotter Pathfinder 18" Radome Smartpilot ST 8001 Auto Pilot Raystar GPS...
View Article[CA] DSM 300 software update
I have a C 80 classic running on V 5.16 software and a DSM 300 running on V4.10 software. I have successfully downloaded the two pkg files and the dob file from Raymarine's web site and transferred...
View ArticleAcronyms and abbreviations used within Raymarine products
Raymarine products and product documents commonly employ abbreviations and acronyms. The following list has been assembled to provide definitions for any such abbreviations and acronyms which may not...
View Article[CA] NEMA 2000 with ST60 and ST4000+
I have 2001 ST60 (speed/depth) and ST4000+ (autopilot) and hope to integrate an Axiom 9 MFD, i70 wind package and Simrad VHF/AIS. Can you point me toward a network diagram ? Thanks, Greg
View Article(DG) ST4000+ and 10 Hz sensor
I am trying to figure out if the ST4000+ (5000+) can use/benefit from a 10 Hz heading sensor. I have an ST4000+ with a rudder sensor, connected to an E80 Classic via Seatalk. The E80 gets its heading...
View Article[CA] E7D switch active with touchscreen locked
I cannot find a way to switch active screens when using split screen with the touchscreen locked. This is something that we need quite frequently. Thanks Graham
View ArticleCP470 Fault-Finding
I am trying to fault-find a CP470 connected to a B265LH, MFD's are e165. The CP470 is flashing the seven flash fault code which according to the manual states it is unable to determine the transducer...
View Article[CA] Axiom pro 9 Chart problem
I have a new Axiom Pro 9 and one of the custom screens for displaying the navigation chart full screen is totally pixelated?? When I go to another screen setup that is split, say for the chart and...
View Article[CA] Front Bezel Color Options
The 2017 catalog lists color options for various instrument and MFD bezels. Is it possible to purchase a black front bezel (vs gunmetal) for an e165?
View Article[CA] AIS Source
Color me confused!!! - While trying to track down why my VHF (SH GX2150 AIS receiver) wasn't getting 183 position data from my e7D - I switched to 4800 baud - now I had position data - but lost AIS...
View Article[CA] Replacement System
Hi Chuck I have a question about the replacement of an ST8002 Head Unit, S2 Computer and Type 1 Pump autopilot system with a P70r, ACU200 & EV1 re-utilizing the Type 1 pump. The owner is unhappy...
View Article[CA] Dual Axiom System
What I have: Axiom pro12 rvx, Axion 12 RV, Flir M232, Ray60, i70s, two rare-sd/usb direct attach to each unit, ev200 power, ais650, ais100 splitter, ST69 speed/temp transom mount with ST POD, RV-100 3D...
View Article[CA] Differences between Navionics and Lighthouse Charts
What are the differences between Navionics and Lighthouse Charts for the Axiom Pro RVX? Thanks.
View Article[CA] New Axiom 7
I have a new Axiom 7 that will be interfaced with older ST60 instruments and a new EV-100. Two questions: 1) Does the Navionics card stay in the MFD, or is it just downloaded after initial power up? 2)...
View Article[CA] Legacy C80 and E80
Hello, I was given 2 Legacy C80 not the wide with radar and with a 250 sonar module. and a E80. I want to be able to have Radar, GPS and Sonar at all three units. Is this possible? I have the cabling...
View Article[CA] Seatalk-ng Coverter Power
I have a Seatalk-ng Converter that sends AIS650 and depth info to my Axiom MFD. Presently the converter gets it power from my S2G AutoPilot computer. I would like to power the Converter via a power...
View Article[CA] c-80 & c-120 installation
I would like to know if the c-80 & c-120 can be interfaced so I can use the radar and chart plotter at either station
View Article[CA] Transducer Change
Hello Support Team, Can a DST800-0 directly replace a existing B17 using same mounting tube, and can be changed while the boat is in the water? Thanks
View ArticleCan a MFD calibrate instrument transducers interfaced to an iTC-5 or...
Can a MFD calibrate instrument transducers interfaced to an iTC-5 or ST70/ST290 pods? MFDs are exclusively capable of calibrating, configuring offsets, configuring alarms associated with the data...
View Article[CA] LH2 Status
Given the recent decision to limit the backward compatibility of LH3 to the eS/gS, what is the status of LH2 for the a/c/e series MFD's?
View Article