Good morning,
I purchased a Quantum Wifi Radar (Q24W) from the Raymarine/FLIR online store.
It arrived last week and I tried to install it last night.
The hardware all went in relatively easily, no issues, and, I wired it directly to a 12v power source.
The problem I'm having is that it won't connect to either one of my Axiom 9 MFD's. However, I can pair it to my iPhone. I've tried just about everything. I'm a little frustrated/confused.
Both my MFD's have the latest Lighthouse release (v3.8.105)
I can see the Radar's WiFi SSID on the Axiom MFD WiFi list, and, from there I can also connect to it (although it obviously says no Internet connectivity)
I just can't seem to get it to connect via the standard Quantum Pairing instructions.
Note: Everything I tried was sitting at my console, about 4 feet from the radar unit itself. The radome is mounted on my fiberglass t-top about 4 feet from the MFD's. It is a small 25 foot center console. I don't believe interference with hull materials would be a factor in my install given the close proximity of the MFD's to the radar, and, the materials that are between the components.
Can I try changing/adjusting the Wifi settings on the MFD itself (like the wifi channel)?
I tried several things like trying to connect to either MFD, both powered on, each one individually with the other one powered off, etc etc..
I even downloaded the RayMarine RayView app and was able to stream my display to my iPhone as suggested in one of the forum posts here. I power cycled the radome and factory reset my MFD's numerous times, etc.
![.jpeg]()
image9.jpeg (Size: 340.39 KB / Downloads: 1)
![.jpeg]()
image8 (1).jpeg (Size: 88.91 KB / Downloads: 1)
![.jpeg]()
image7 (1).jpeg (Size: 121.24 KB / Downloads: 1)
![.png]()
image6.png (Size: 93.38 KB / Downloads: 1)
![.jpeg]()
image5 (1).jpeg (Size: 88.08 KB / Downloads: 1)
![.jpeg]()
image3 (3).jpeg (Size: 80.64 KB / Downloads: 1)
![.jpeg]()
image2 (5).jpeg (Size: 66.13 KB / Downloads: 1)
![.jpeg]()
image1 (16).jpeg (Size: 78.7 KB / Downloads: 1)
I purchased a Quantum Wifi Radar (Q24W) from the Raymarine/FLIR online store.
It arrived last week and I tried to install it last night.
The hardware all went in relatively easily, no issues, and, I wired it directly to a 12v power source.
The problem I'm having is that it won't connect to either one of my Axiom 9 MFD's. However, I can pair it to my iPhone. I've tried just about everything. I'm a little frustrated/confused.
Both my MFD's have the latest Lighthouse release (v3.8.105)
I can see the Radar's WiFi SSID on the Axiom MFD WiFi list, and, from there I can also connect to it (although it obviously says no Internet connectivity)
I just can't seem to get it to connect via the standard Quantum Pairing instructions.
Note: Everything I tried was sitting at my console, about 4 feet from the radar unit itself. The radome is mounted on my fiberglass t-top about 4 feet from the MFD's. It is a small 25 foot center console. I don't believe interference with hull materials would be a factor in my install given the close proximity of the MFD's to the radar, and, the materials that are between the components.
Can I try changing/adjusting the Wifi settings on the MFD itself (like the wifi channel)?
I tried several things like trying to connect to either MFD, both powered on, each one individually with the other one powered off, etc etc..
I even downloaded the RayMarine RayView app and was able to stream my display to my iPhone as suggested in one of the forum posts here. I power cycled the radome and factory reset my MFD's numerous times, etc.
image9.jpeg (Size: 340.39 KB / Downloads: 1)
image8 (1).jpeg (Size: 88.91 KB / Downloads: 1)
image7 (1).jpeg (Size: 121.24 KB / Downloads: 1)
image6.png (Size: 93.38 KB / Downloads: 1)
image5 (1).jpeg (Size: 88.08 KB / Downloads: 1)
image3 (3).jpeg (Size: 80.64 KB / Downloads: 1)
image2 (5).jpeg (Size: 66.13 KB / Downloads: 1)
image1 (16).jpeg (Size: 78.7 KB / Downloads: 1)
